Textile folding machine installation method

1. When the folding machine is transported by the manufacturer to your laundry room, you must first check the dryer regularly to check whether it is the machine you purchased and whether it is damaged or unusable during the transportation process. If there is a problem, take photos immediately and contact the manufacturer.
2. Before the folding machine, you should determine the installation position of the dryer. The installation position of the folding machine should consider the location of the transportation channel, raw material turnover, water inlet, steam inlet and sewer pipe. Here, the Xingxing washing equipment reminds you that the folding machine should be installed. Together with equipment such as dehydrators and dryers, the distance between these devices is reduced to prevent subsequent troubles due to improper selection of locations.
3. The textile folding machine belongs to one of the larger and heavier laundry equipments, so the machine should be installed on a solid foundation and kept at the same level to prevent the equipment from working due to the uneven location of the site and the installation location. Large vibrations occur, which affects the washing efficiency and the service life of the dryer.
4. Refer to the instruction manual of the folding machine, and find the electric control cabinet door of the folding machine according to the relevant contents in the manual. Connect the 380V three-phase power supply line and the neutral line according to the binding post. (There is to be reminded that the power of the folding machine must be 380V, no access to low voltage or high voltage)
5. Refer to the folding body label to indicate the corresponding access to the water inlet pipe and the steam pipe. If the steam condition is not available, the steam inlet port may be blocked. If steam heating is used, install pressure indicating devices and safety devices at the obvious location of the steam main pipe outside the machine.
Precautions´╝Ü
1. The installation of the folding machine is completed through the above five steps. At the time of installation, we should also pay attention to the following problems: the installation environment of the folding machine is best for dry, ventilated, clean working environment, good working environment and extended drying The key factor in the service life of the dryer.
2. When installing, you should strictly refer to the installation contents provided by the manufacturer to carry out the step-by-step operation. Do not install it according to your own feelings.
3. When there is a problem during installation, you should contact the manufacturer at the first time.

Source: Baidu Encyclopedia

Weaving-fabric manufacture

The weaving process uses a loom. The lengthway threads are known as the warp, and the cross way threads are known as the weft. The warp, which must be strong, needs to be presented to loom on a warp beam. The weft passes across the loom in a shuttle, that carries the yarn on a pirn. These pirns are automatically changed by the loom. Thus, the yarn needs to be wrapped onto a beam, and onto pirns before weaving can commence.

Winding
After being spun and plied, the cotton thread is taken to a warping room where the Fabric winding machine ( WITH DIRECT CENTRE DRIVEN SYSTEM )takes the required length of yarn and winds it onto warpers bobbins
Warping or beaming textile

Racks of bobbins are set up to hold the thread while it is rolled onto the warp bar of a loom. Because the thread is fine, often three of these would be combined to get the desired thread count.
Sizing
Slasher sizing machine needed for strengthening the warp by adding starch to reduce breakage of the yarns.
Drawing in, Looming
The process of drawing each end of the warp separately through the dents of the reed and the eyes of the healds, in the order indicated by the draft.
Pirning (Processing the weft)
Pirn winding frame was used to transfer the weft from cheeses of yarn onto the pirns that would fit into the shuttle
Weaving
Main article: Power loom
At this point, the thread is woven. Depending on the era, one person could manage anywhere from 3 to 100 machines. In the mid nineteenth century, four was the standard number. A skilled weaver in 1925 would run 6 Lancashire Looms. As time progressed new mechanisms were added that stopped the loom any time something went wrong. The mechanisms checked for such things as a broken warp thread, broken weft thread, the shuttle going straight across, and if the shuttle was empty. Forty of these Northrop Looms or automatic looms could be operated by one skilled worker.

A Draper loom in textile museum, Lowell, Massachusetts
The three primary movements of a loom are shedding, picking, and beating-up.
Shedding: The operation of dividing the warp into two lines, so that the shuttle can pass between these lines. There are two general kinds of sheds-“open” and “closed.” Open Shed-The warp threads are moved when the pattern requires it-from one line to the other. Closed Shed-The warp threads are all placed level in one line after each pick.
Picking:The operation of projecting the shuttle from side to side of the loom through the division in the warp threads. This is done by the overpick or underpick motions. The overpick is suitable for quick-running looms, whereas the underpick is best for heavy or slow looms.
Beating-up: The third primary movement of the loom when making cloth, and is the action of the reed as it drives each pick of weft to the fell of the cloth.
The Lancashire Loom was the first semi-automatic loom. Jacquard looms and Dobby looms are looms that have sophisticated methods of shedding. They may be separate looms, or mechanisms added to a plain loom. A Northrop Loom was fully automatic and was mass produced between 1909 and the mid-1960s. Modern looms run faster and do not use a shuttle: there are air jet looms, water jet looms and rapier looms.

Automated Camera Inspection System

Newly launched Automated Camera Inspection System. Applicable for weaving machine, warp knitting machine, fabric inspection machine, stenter, compactor, etc. With camera online checking and the max. speed is upto 80m/min; The defects with 0.15mm size could be mapped and recorded. 5 times high efficiency compared with traditional manpower checking; 24 hours online working!!

Suntech, No.1 brand in China for Fabric Make-up Machines and Material Storage & Handling Equipments.
Email:sales7@suntech-machinery.com
Webpage: http://www.suntech-machine.com


20180913144851Video link

Tubular fabric roll slitting machine

Feature( Tubular fabric roll slitting machine ):

This machine is the auxiliary products of the automatic mould cutting machine , which is suitable for narrow pieces of paper being cut. It have count no. Automatically, put roll rectify a beviation the functions of controlling etc.automatically by three photoelectric eyes, the structure of the complete machine is compact, fast with high efficiency,operate the characteristic simply, operate steadily.

Charatertistics ( fabric roll slitting machine ):

1. The max width: 550mm
2. The minimum slitting width: 8-20mm
3. Material thickness range: 0.05-3mm
4. Tolerence: 0.2mm, Precision: 0.1mm
5. The speed:70m/min

6. Under CE and ISO
7. Manufacturer experience: 30years
8. Export experience: 10years

Functions ( fabric roll slitting machine ):

1. This machine is applicable to slit the narrow scope paper and tape.
2. It can automatically meter, set length, stop, winding is controlled by photoelectric eyes.
3. Compact structure, fast speed, high efficiency, accurate slitting, easy and steady operation.

Purpose( fabric roll slitting machine ):

1. It is applicable for the slitting tooling of industrial adhesive tape, electronic material, protective film, copper foil, aluminum foil, OPP, PE, PVC, sheet, cloth, etc.
2. This machine is widely used in the industries such as printing, packing, electronics, leather, clothes making, plastic, etc.